My boat just got it's end of season service and the mechanic has advised that the shims in the motor (a 200 hp Suzuki) no longer meet the manufacturer's specs & have to be adjusted. To do it will require a day to a day and a half of labor - approx $1 - 1.5K. I have a 2017 24 SPDX tritoon. Anyone heard of this & any comments would be appreciated. Thanks,
Shims in my 200hp Suzuki out of specs
- Thread starter SpartyBob
- Start date
Jack M
Moderator
I would contact Suzuki . You can Google their contact info .
Thanks, good tip. I’ve been in contact with the dealer that sold me the boat, Dewitt Marine, but am still waiting for a return call … However I just went on the Suzuki site & filled out their dealer contact form, which goes to Dewitt via Suzuki, so at least there’s something on record.
sunedog
Well-Known Member
- Messages
- 658
- Reaction score
- 1,230
This is crazy. So many questions. Can you post some pics?
Did this dealer install the offending shims?
Did the offending shims meet the manufacturer's spec when the boat was purchased from this dealer?
I've never heard of outboard motor shims. Are they between the transom and the motor? Why would it take a day to a day and a half to swap them?
What, exactly, is different between the current shims and the different shims currently specified by the manufacturer?
Vikingstaff
Moderator
Ditto every question. Whole situation on a 2017 seems weird.
I guess its either valvetrain shims
Tappet Clearance - Suzuki DF200 Service Manual [Page 41]
Suzuki DF200 Manual Online: Tappet Clearance. Inspect initially after 20 hours (1 month) and every 200 hours (12 months). The tappet clearance specification is different for intake and exhaust valves. Too small a tappet clearance may reduce engine power, too large a tappet clearance...
www.manualslib.com
or its gearcase shims on the lower unit for fwd and reverse.
Lower Unit Gears-Shimming And Adjustment - Suzuki DF 90 Service Manual [Page 278]
Suzuki DF 90 Manual Online: Lower Unit Gears-Shimming And Adjustment. 9-24 LOWER UNIT LOWER UNIT GEARS- SHIMMING AND ADJUSTMENT If lower unit has been rebuilt or has had components replaced, shimming for correct gear contact and backlash will have to be adjusted to ensure smooth,...
www.manualslib.com
Last edited:
BigKahuna
Well-Known Member
Shims?!? Do they wear out or what?!?
Potomacbassin’
Well-Known Member
1.5 days of labor sounds completely unreasonable. It's probably the valve clearance check scheduled for your engine every 200-300 hours and while it may (or may not) be out of spec, I think it's also important to consider how FAR out of spec a particular valve is. Very close to spec? Maybe just keep an eye on it. Far out of spec? Maybe it just makes noise, or the valve itself is wearing and shim needs replacement.
OP do a search on a site like THT where you'll find many more experts on the matter. Many engines never have these checked or adjusted and live happy, long noisy lives. OR it could end up voiding your warranty down the road. A second opinion from another dealer might also prove instructive (especially if they can provide the measurements to you to cross-verify against the original dealer).
OP do a search on a site like THT where you'll find many more experts on the matter. Many engines never have these checked or adjusted and live happy, long noisy lives. OR it could end up voiding your warranty down the road. A second opinion from another dealer might also prove instructive (especially if they can provide the measurements to you to cross-verify against the original dealer).
PartyBarge
Well-Known Member
- Messages
- 361
- Reaction score
- 370
Any new info on if the "shims" are in the power head or the lower unit? In any event, this sounds suspiciously like parts that were not properly heat-treated or not the correct alloy. IF SO, this should be along the lines of a recall and not totally owner responsibility. Good luck, stay alert to this as a problem with EOM defective parts...
Last edited:
Willes
Active Member
- Messages
- 37
- Reaction score
- 32
I have the same motor. I’m following to see the outcome.
lakeliving
Well-Known Member
Sounds like someone is trying to shim some money out of your wallet.
DVW
Well-Known Member
- Messages
- 366
- Reaction score
- 646
I am going to assume your motors valve lash no longer meets spec and will require a different thickness shim to bring it into spec. Attached is a screen shot of your valve train. The shim is part #13. I have done this job on a Suzuki motor and have had it done on a Yamaha motor. Both motors where in snowmobiles but the basic design of the valve train is the same. The Yamaha required camshaft removal taking a full day by a skilled mechanic. Most mechanics might use the same process with the Suzuki but when I worked on my snowmobile there was tool available that eliminated camshaft removal. Camshaft removal is more than half the job. I made my own tool but it still took me far more than a day because I am no mechanic.